Deye • Sunsynk • Sol-Ark • Pylontech • Fogstar • Dyness • V-TAC

Deye inverter læser ikke alle batterier (2. eller 3. LiFePO4 modul)

Har du 2 eller 3 LiFePO4-batterier koblet parallelt på din Deye inverter, men Li-BMS viser kun halv Ah-kapacitet? Sikker og gratis fjerndiagnose.

Estimeret Årligt Tab

A single 10 kWh LiFePO4 module worth 2,000–3,500 € sitting idle due to BMS addressing costs 320–550 € per year in lost self-consumption and accelerates wear on active packs.

Elsikkerhed & Garantibeskyttelse (Undgå blinde forsøg ud fra generiske AI- eller forumsvar)

LiFePO4 husstandsbatterier arbejder med jævnstrøm på 100–250 Ampere DC. At ændre DIP-switches eller bytte RJ45-kabler i blinde kan brænde BMS-kortet af og annullere garantien. Vores fjerndiagnose aflæser først dine registre 100 % skrivebeskyttet (read-only) uden risiko (EU VIES CVR/moms IT04226190041 — Vasile Bratu, Data Engineer).

Common Symptoms Seen in Solarman / Sunsynk Connect / Deye Cloud

  • •You paid for 2 or 3 LiFePO4 modules in parallel, yet the Li-BMS screen reports only 100 Ah, 200 Ah, or 400 Ah instead of the combined bank capacity.
  • •One battery module sits idle at 0.0 A charge/discharge while the remaining packs hit 100% early or drain to cutoff every evening.
  • •Maximum charge/discharge current (Amps) is automatically throttled because the master BMS cannot enumerate slave packs on the bus.

What We Check Remotely for Free (0 €, Read-Only)

  • ✓Live Li-BMS register inspection comparing reported Ah capacity against your physically installed kWh.
  • ✓Cross-check of CAN/RS485 protocol selection, master-slave port topology, and logical pack addressing without touching live DC wiring blindly.
  • ✓Pack-to-pack voltage delta check prior to parallel synchronization to prevent high-current inrush.
Transparent 2-Step Protocol: 1) Read-only telemetry diagnosis (no password required) and annual loss calculation are 100% free (0 €). 2) Only after reviewing your diagnostic report do you decide whether to unlock remote optimization (75 € fixed fee paid prior to intervention with official invoice, or 7-day free BPS™ Cloud Autopilot trial).
ANBEFALET TEKNISK TILBEHØR • 15–45 €
DC MCB Afbryder 125A (48V LiFePO4)

Dedikeret DC-afbryder til sikker beskyttelse og isolering af parallelle 48V/51,2V LiFePO4-batteribanker.

Se pris på Amazon →
Verified Case Study • Rome (November 2026) Read full case & client reviews →
Leonardo P. (Rome, IT) — Deye Hybrid Inverter + 3x V-TAC LiFePO4 Batteries (30.72 kWh)

Three physical LiFePO4 modules were installed on the wall, yet BMS-to-inverter addressing restricted usable storage. Via read-only Solarman register diagnosis and 20-minute guided alignment, the full bank unlocked 600 Ah / 30.72 kWh active capacity and 4.93 kW live output.

Frequently Asked Questions (FAQ)

Should I flip DIP switches or swap RJ45 cables myself based on forum posts?

Never guess blindly: different battery revisions use incompatible RJ45 pinouts (CANH/CANL vs RS485) and binary vs decimal DIP addressing. A wrong pinout can damage the BMS transceiver. Our free read-only check identifies your exact bus state first.

Do you need my Solarman or Sunsynk password?

No. Initial diagnosis uses standard read-only plant sharing or diagnostic register snapshots — never your personal password.

Other Remote Inverter & Battery Diagnostic Guides